Products List
Ultrafine Mill Machine
Author:liming Post Date:2013-1-26
Ultrafine Mill Machine
Ultrafine Mill Machine Introduction:
Ultrafine mill machine is independently developed a new mechanical grinding equipment, its low energy consumption, set centrifugal crushing, impact crushing, squeezing crushed in an energy saving 40 to 50% higher than other types of mechanical grinder. The high fineness: with the grading system from Split, the product fineness ≥ 2500 mesh, feeding, feed size ≤ 50mm material only the a coarse broken equipment. Low abrasion, crushing part of the wearing parts the composite wear new material, long service life, pollution-free processing Mohs hardness ≤ 5 material.
Ultrafine Mill Machine Performance Characteristics:
Ultrafine mill machine, we produce the product features, needle-like material can be crushed, crushing process temperature rise, suitable for heat-sensitive materials crushed on sintering reunion ultrafine materials scattered jobs, granular recovery rate of 100%particles having a shaping function, improve the bulk density, and can crush the material of the fibrous tissue, and also having a drying function. Its production of negative pressure, no dust pollution, environmental quality, and high degree of automation, stability, easy to operate, can reduce the cost of the investment, the companies have chosen the best milling equipment.
Ultrafine Mill Machine Installation:
Install ultrafine mill machine run the site have not been installed, you should take good care of the exposed surfaces are coated with anti-rust grease, and avoid the sun and rain, to prevent the body rust water, To establish maintenance system. Plant and foundation should have enough height and installation location of the installed base size of the chart according to Raymond, Raymond should be based on high-standard cement and shall be buried reinforced before being placed foundation, and I buried conduit or cable trench. After pouring the cement foundation, there must be a 15-day maintenance period. Should be 2 to 3 tons with a lifting tool for Raymond installation maintenance. Raymond from the factory to use over six months, to host the central axis of the system, the transmission roller device, and analysis of oil pools should be cleaned inspection, cleaning checked respond to the various components add sufficient lubricant.
Ultrafine Mill Machine Work Process:
Will need to crush the material uniformly continuous fed into the grinding chamber, scoop up material sent between the roller and grinding ring rotates, centrifugal force, grinding roller swings out, pressed on the grinding ring blade, because of the grinding rollersrolling the reach crushed purpose.
Material after grinding, grinding into the analysis with the blower circulating air separation, fine through coarse material Rockwell will re-grinding, qualified powder into the finished product cyclone powder collector with the flow discharged stone tube, that is for the finished product.
Materials in the grinding room was grinding some moisture, grinding heat, moisture evaporation, and the whole pipe interface is not tight, the outside air is inhaled, the circulation increased pressure to ensure that the mill work in the vacuum state , the increase in gas flow through the I wind tube into the dust collector, into the atmosphere after being purified.
Ultrafine Mill Machine Structural Features:
1, the three-dimensional structure, small footprint, sets strong from the block not expect the finished powder independence its own production system.
2, refined powder fineness of uniform through screening rate of 99%, it is difficult to have other milling equipment.
3, host transmission with sealed gear box and pulley transmission smooth, reliable operation.
4, important parts are made of high-quality steel, wear-resistant parts are made of high-performance wear-resistant materials, the whole high wear resistance, reliable operation.
5, the electrical system with centralized control, milling workshop basic unmanned operation, and maintenance.
Liming Ultrafine Mill Machine:
Liming Heavy Industry is committed to producing the best mechanical crushing equipment, capable of producing various types of crusher and mill, and reached the leading level in the world. We are a trustworthy ultrafine mill machine manufacturer capable of producing all types of ultrafine mill machine, good quality and reasonable prices. Liming Heavy Industry production of ultrafine mill machine is a set of similar products at home and abroad, the successful experience, devote themselves to come up with an energy-efficient crushing equipment. Medium-sized ultrafine mill machine is one of the leading products of the company, especially in the design and production of large crusher mill at the absolute leading level at home and abroad.
If you need any help of ultrafine mill machine, please contact us directly. We aim to provide you with the best ultrafine mill machine and the most economical reasonable solution, our experts will provide technical assistance at any time for you. Looking forwards to establish a long-term business relationship with you.